INSTRUCTIONS
FOR THE PREPARATION AND FORMAT
OF A CAMERA-READY PAPER: SIXTH INTERNATIONAL
CONFERENCE
ON
OF A CAMERA-READY PAPER: SIXTH INTERNATIONAL
CONFERENCE
ON
UNCONVENTIONAL
ELECTROMECHANICAL AND ELECTRICAL SYSTEMS
ALUSHTA, THE CRIMEA, UKRAINE, SEPTEMBER 24-29, 2004
***
Only on the 1st page, please leave a free field for organizers: 4 cm from
the top margin ***
|
Affiliation, address [12pt]
|
|
|
TITLE OF THE PAPER
[14 pt Bold, centred]
|
|
Key words: Here 5 - 8 key words should be presented. [12pt]
|
|
Abstract: Should include only the main information about the content. It should not exceed
8 - 10 lines with a single indentation. [11 pt]
|
|
|
|
TITLE OF THE PAPER
[14 pt Bold, centred]
|
|
Key words: Here 5 - 8 key words should be presented. [12pt]
|
|
Abstract: Should include only the main information about the content. It should not exceed
8 - 10 lines with a single indentation. [11 pt]
|
|
|
_ __ __The language of papers is English.
The full text should contain an even number of pages (four or
six). The paper should be prepared and printed in one column
format on A4 size paper (297 x 210 mm). Typing is to be single spaced,
left and right justified, and as close as possible to the fonts used in
Table 1. An empty line should separate chapters, figures and tables. Headings
should be presented as given in this instruction. The first line of each
paragraph should be indented by 1.25 cm. No full stop should be put at
the end of a heading when written in capitals. No single letter or conjunction
should be left at the end of a line. Numbering of pages will be done by
the publisher. Authors should write the number of each page at its back
(by pencil in the right top corner). The text should be printed in laser
quality (300 dots/in or better) on a high quality white sheets paper.
Each contribution should be supplied in 2 paper copies and, in addition,
on a diskette or e-mail. Note that failure to comply with the requests
of the instructions may result in your paper being omitted from reviewing
and publication in the Conference Proceedings.
|
|
Required page parameters:
First page: top margin 6 cm, left margin 2.5 cm, right margin 2.5 cm, bottom margin 3 cm;
Next pages: top margin 2 cm, left margin 2.5 cm, right margin 2.5 cm, bottom margin 3 cm.
|
2. FIGURES AND TABLES
|
..............The
table caption should be typed above the table, and that of a figure beneath
the figure. In both cases the caption should be typed single spaced flush
to left-hand and right-hand sides of the table (figure) with its last
line being centred. A one line caption should be centred. Figures up to
90 mm wide should be wrapped around by the text. Use the abbreviation
"Fig. 1". Around the contour of the figure should be a free
field up to 7 mm wide. Avoid placing figures and tables before their first
mentioning in text.
|
TABLE 1. Required font parameters
|
Title
of the paper |
Abstract,
references, tables and figure captions |
Heading |
Subheading |
Text of the paper |
TIMES
NEW ROMAN, 14 PT BOLD, CAPITAL |
Times
New Roman, 11 pt |
TIMES
NEW ROMAN, 12 PT BOLD, CAPITAL |
Times
New Roman, 12 pt Bold |
Times
New Roman, 12 pt |
|
|
|
|
|
Ua
= Ub = Uc = I•R ............. .... ................................................(1)
(an
editor of equations to be used!)
...............Be
sure that the symbols in the equation have been defined before the equation
appears or immediately following. Use "(1)", not "Eq. (1)"
or "equation (1)", except at the beginning of a sentence: "Equation
(1) is...".
|
|
|
|
................In
this place, the authors gratefully acknowledge the contributions (scientific
and financial) of various persons and institutions. [12 pt].For example:
Financial backing: Polish State Committee for Scientific Research Grant No. 108/E-364/BW/97
Financial backing: Polish State Committee for Scientific Research Grant No. 108/E-364/BW/97
|
|
............References
should be collected at the end of the paper. The system in which they
should be numbered is shown below [11 pt]:
1. Yamamura S. Theory of linear induction motors (2nd ed.). University of Tokyo Press, Tokyo, 1978.
2. Gieras J.F. Electrodynamic forces in electromagnetic levitation systems. Acta Technica CSAV, 1982, No. 5, pp. 532 - 545.
3. Afonin A., Szymczak P., Bobako S. Linear drives with controlled current layer. Proc. First Int. Symp. on Linear Drives for Industry Applications LDIA'95. Japan, 31 May - 2 June 1995,
pp. 275 - 278.
1. Yamamura S. Theory of linear induction motors (2nd ed.). University of Tokyo Press, Tokyo, 1978.
2. Gieras J.F. Electrodynamic forces in electromagnetic levitation systems. Acta Technica CSAV, 1982, No. 5, pp. 532 - 545.
3. Afonin A., Szymczak P., Bobako S. Linear drives with controlled current layer. Proc. First Int. Symp. on Linear Drives for Industry Applications LDIA'95. Japan, 31 May - 2 June 1995,
pp. 275 - 278.